5
3. Pull and hold the trigger through the operation.
When the cut is complete or the tool shuts off,
release the trigger. An LED will light when the
trigger is pulled.
NOTE:
Workpiece may move
slightly during the cut.
4. Pull the reverse switch to retract the rear blade.
WARNING
To reduce the risk of injury, only
cut recommended materials for the
jaws (see "Specifications"). Do not attempt to cut
other materials.
Cutting Tips
• Cut farther in from the end of the material to avoid
crooked cuts.
•
Do not attempt angled cuts as it will damage the blades.
Hold the material squarely between the blades.
•
Cut clean material to extend the blade life. Wipe dirt
and debris from material and blades before begin-
ning the cut.
Jammed Blades
Dirt and debris can cause the blades to become
jammed together after a cut. If the rear blade does
not retract when the reverse switch is pulled:
1. Press and hold the reverse switch to ensure the
tool has reset.
2. Remove the battery pack.
3. Press the jaw release levers and pull the reverse
switch to attempt to open the jaws. If the jaws un
-
latch, use a soft mallet to tap the front blade open.
4. If the jaws will not unlatch, pull the reverse switch and
tap the rear blade ram until the rear blade retracts.
5. Clean any dirt and debris from the blades before
starting another cut.
MAINTENANCE
WARNING
To reduce the risk of injury, always
unplug the charger and remove the
battery pack from the charger or tool before
performing any maintenance. Never disassemble
the tool, battery pack or charger. Contact a
MILWAUKEE service facility for ALL repairs.
Maintaining Tool
Keep your tool, battery pack and charger in good
repair by adopting a regular maintenance program.
Inspect your tool for issues such as undue noise,
misalignment or binding of moving parts, breakage of
parts, or any other condition that may affect the tool
operation. Return the tool, battery pack, and charger
to a MILWAUKEE service facility for repair. After six
months to one year, depending on use, return the
tool, battery pack and charger to a MILWAUKEE
service facility for inspection.
If the tool does not start or operate at full power with
a fully charged battery pack, clean the contacts on
the battery pack. If the tool still does not work prop
-
erly, return the tool, charger and battery pack, to a
MILWAUKEE service facility for repairs.
Jaws and Blades
Inspect jaws for cracks or damage. Do not use dam
-
aged jaws. Replace the blades when they become
chipped or damaged.
Service Interval
Refer to the ONE-KEY™ App for information regard-
ing necessary servicing, such as fluid replacement.
Return the tool to a MILWAUKEE service facility for
all repairs and maintenance.
ONE-KEY™
WARNING
Chemical Burn Hazard.
This device contains a
lithium button/coin cell battery. A new
or used battery can cause severe in
-
ternal burns and lead to death in as
little as 2 hours if swallowed or enters the body.
Always secure the battery cover. If it does not
close securely, stop using the device, remove the
batteries, and keep it away from children. If you
think batteries may have been swallowed or en
-
tered the body, seek immediate medical attention
.
Internal Battery
An internal battery is used to facilitate full ONE-KEY™
functionality.
To replace the battery:
1. Remove the battery pack.
2. Remove the screw(s) and open the battery door.
3. Remove the old battery, keep it away from children,
and dispose of it properly.
4. Insert the new battery (3V CR2032), with the posi
-
tive side facing up.
5. Close the battery door and tighten the screw(s)
securely.
WARNING
To reduce the risk of personal in-
jury and damage, never immerse
your tool, battery pack or charger in liquid or
allow a liquid to flow inside them.
Cleaning
Clean dust and debris from vents. Keep handles
clean, dry and free of oil or grease. Use only mild
soap and a damp cloth to clean, since certain clean-
ing agents and solvents are harmful to plastics and
other insulated parts. Some of these harmful agents
include gasoline, turpentine, lacquer thinner, paint
thinner, chlorinated cleaning solvents, ammonia and
household detergents containing ammonia. Never
use flammable or combustible solvents around tools.
Repairs
For repairs, return the tool, battery pack and charger
to the nearest service center.
ACCESSORIES
WARNING
Always remove battery pack before
changing or removing accesso-
ries. Only use accessories specifically recom
-
mended for this tool. Others may be hazardous.
For a complete listing of accessories, go online to
www.milwaukeetool.com or contact a local distributor.
SERVICE - UNITED STATES
1-800-SAWDUST
(1.800.729.3878)
Monday-Friday, 7:00 AM - 6:30 PM CST
or visit
www.milwaukeetool.com
Contact Corporate After Sales Service Technical
Support with technical, service/repair, or warranty
questions.
Email: [email protected]
Become a Heavy Duty Club Member at
www.milwaukeetool.com to receive important
notifications regarding your tool purchases.
