5
Per NFPA 70E
All steps must be completed in order! Once started,
steps 1-4 must be completed with no more than
5 minutes between each step. If more than 5 minutes
occurs, reset (see step 7) and begin again.
1.
Turn
ON
( ) the remote cut switch on
the tool to disable the trigger and turn
on the wireless function.
The tool's remote cut light will be
steady red.
2.
WARNING!
Ensure the remote
cut switch is
ON
before pulling
the trigger.
Pull the trigger (1) and slide the
1
2
trigger lock to
(2).
The tool's remote cut light will
be flashing red.
WARNING!
During the cut, remain outside the arc
flash boundary in accordance with NFPA 70E for the
system being cut.
3.
Turn
ON
(I) the remote.
1
2
1 2
1.
2.
3.
4.
5.
6.
ON THE TOOL:
Turn ON (I) the remote cut
switch on the tool.
Remote cut light steady red.
To make the cut, press and
hold button 3 for 2 seconds.
Light 3 steady red.
Release button 3, cutting will begin.
Pull the trigger and
slide the trigger lock to .
Remote cut light flashing red.
Turn
Light 1 steady blue.
Light 2 flashing red.
ON (I) the remote.
Press and hold button 2 for
2 seconds.
Light 2 steady red.
Light 3 flashing red.
TO RESET:
Pull the trigger (1) to unlock.
Pull the release trigger (2) to
reset the jaws. Turn OFF the
remote cut switch (3).
When the cut is complete, the
cut indicator will light:
Green = Done Cutting
Red = Cut Failed
2
sec
2
sec
3
7.
Light 1 will be steady
blue.
Light 2 will be flashing
red.
NOTE:
Light 1 flashing
blue and Light 2 off indicates the remote is
out of range of the tool. Move the remote
closer to the tool.
4.
Press and hold button 2 for
1 2
4.
5.
6.
To make the cut, press and
hold button 3 for 2 seconds.
Light 3 steady red.
Release button 3, cutting will begin.
Press and hold button 2 for
2 seconds.
Light 2 steady red.
Light 3 flashing red.
TO RESET:
Pull the trigger (1) to unlock.
Pull the release trigger (2) to
reset the jaws. Turn OFF the
remote cut switch (3).
When the cut is complete, the
cut indicator will light:
Green = Done Cutting
Red = Cut Failed
2
sec
2
sec
3
7.
2
sec
2 seconds.
Light 2 will be steady
red.
Light 3 will be flashing
red.
5.
Within 20 seconds,
press and
1 2
6.
2
sec
3
7.
2
sec
hold button 3 for 2 seconds
to begin the cut.
Light 3 will be steady
red.
Release button 3, cutting will begin.
Note, if more than 20 seconds passes between
step 4 and 5, reset (see step 7) and begin again.
6.
When the cut is complete, the
cut indicator will light:
Green = Done Cutting
Red = Cut Failed
7.
To reset, pull the trigger (1) to
1 2
3
unlock.
Pull the release trigger (2) to
reset the jaws.
Turn
OFF
the remote cut switch
(3).
Cutting without Remote
•
Before cutting, ensure blades are properly installed.
• The tool can be set on the ground or hand held
during use. To set the tool on the ground, rotate
the cutting head 180° to use the front handle as a
"foot". To hold by hand, grasp the tool firmly by both
handles, as shown.
•
Insert the workpiece squarely between the blades.
Do not attempt to make angled cuts as it will dam-
age the workpiece and blades.
• Ensure the remote cut switch is turned to
OFF
.
1. Grasp handle(s) firmly and pull and hold the trigger
through the operation. When the cut is complete or
the tool shuts off, release the trigger. An LED will
light when the trigger is pulled.
NOTE:
Workpiece
may move slightly during the cut.
2.
When the cut is complete, pull the release trigger
to open the blades.
WARNING
To reduce the risk of injury, only
cut recommended materials for the
blades (see "Specifications"). Do not attempt to
cut other materials.
Cutting Tips
• Cut farther in from the end of the material to avoid
crooked cuts.
•
Do not attempt angled cuts as it will damage the blades.
Hold the material squarely between the blades.
•
Cut clean material to extend the blade life. Wipe dirt
and debris from material and blades before begin-
ning the cut.
•
Use the trigger lock to lock-off the trigger when the
tool is not in use.
