Milnor 42044SR2 Mechanical Parts And Service Download

Page: 144 / 161

142

Pellerin Milnor Corporation

BNWUUM02 / 2020084

BNWUUM02

0000277470

2/19/20 8:47 AM

Released

Servicing Air Cylinders

BNWUUM02.T01 0000277469 A.3 A.2 2/18/20 3:01 PM Released

This is the general procedure for rebuilding an air cylinder using a Milnor

furnished repair kit,

once the air cylinder has been removed from the machine. See the specific air cylinder and major
assembly parts drawing(s) for component identification and removal/replacement information.

Maintenance procedures require:

•

Two threaded rods and nuts, twice the length of the tie bolts.

•

The appropriate repair kit.

CAUTION:

EXPLOSION HAZARD —

Spring tension can cause air cylinder to burst

apart with great force during dissassembly. You can be struck by air cylin-
der parts.

�

Follow maintenance instructions carefully.

�

Wear eye protection.

NOTE:

Use a new locknut when re-assembling air cylinder (see the appropriate parts

drawing).

1. Replace two diagonally opposite tie bolts with threaded rods and nuts as shown in

Figure 41:

Using Threaded Rods, page 142

2. Tighten nuts on the threaded rods until they contact the air cylinder.

3. Remove the other two tie bolts and the nuts, washers, clips, and actuators from the external

end of piston stem.

Figure 41.

Using Threaded Rods

Legend

A...

Tie bolt

B...

Threaded rod

C...

Piston stem

4. Loosen nuts on threaded rods evenly, permitting cylinder heads to separate. Use only a few

turns on one nut before moving to the other one. Continue until springs have no tension.

Water and Steam Piping and Assemblies

Summary of Contents for 42044SR2


































































































































































Search results

Summary of Contents for 42044SR2

Reviews:

Related manuals for 42044SR2

Brands by name

Popular brands

Milnor 42044SR2, Mechanical Parts And Service

Search results

Summary of Contents for 42044SR2

Reviews:

Related manuals for 42044SR2

Brands by name

Popular brands