background image

82

Pellerin Milnor Corporation

Figure 34.

Measuring Bearing Unmounted Clearance (bridge for 42" machine shown)

5. Try to pull the gauge straight out. If it comes out, increase the size of the gauge by .001". If it

does not come out, decrease the gauge by .001". The thickest feeler gauge that will come out
is the unmounted internal clearance of the bearing.

6. Compare the measured clearance with the “Unmounted Clearance” in

Table 24: Table of

Bearing Clearances, page 82

If the measured clearance is not within the range shown, do not

use the bearing. Contact your bearing supplier for an exchange.

NOTE:

The clearances listed in the chart are industry standards and therefore apply

to all brands of bearings supplied by Milnor

®

. If other sources of bearings are used, re-

fer to the manufacturer’s instructions for proper clearances.

NOTE:

To locate your bearing on the chart, match the first five characters of the

manufacturer’s part number (

not the

Milnor

®

part number

) with those in the chart.

For example, for a manufacturer’s part number 22217LBK, find under “Manufacturer
Part Number” the line “22217 . . .”

Table 24.

Table of Bearing Clearances

Manufacturer Part Number

Unmounted Clearance

Clearance Reduction

Minimum

Maximum

Minimum

Maximum

22330...

.0071

.0091

.002

.003

22213...

.0030

.0039

.001

.002

22216...

.0028

.0037

.001

.002

22217...

.0044

.0057

.0015

.0025

22312...

.0030

.0039

.001

.002

22316...

.0037

.0049

.001

.002

22320...

.0044

.0057

.0015

.0025

22328...

.0063

.0081

.002

.003

23220...

.0044

.0057

.0015

.0025

Bearing Assemblies

Summary of Contents for 42044SR2


































































































































































Reviews: