manualshive.com logo in svg

Miele WKG 120 WCS, Operating Instructions Manual

Share
Download
Miele WKG 120 WCS Operating Instructions Manual Download Page 67

Problem solving guide

67

The door will not open

Problem

Cause and remedy

The door cannot be
pulled open during a
programme.

The drum is locked during a programme.

Press the 

Start/Stop

 button.

Use the 

 sensor to select 

Cancel programme

 or

Add laundry

.

The door will unlock and you will be able to pull it
open.

There is still water in the drum and the machine is
unable to drain.

Clean the drain filter and the drain pump as
described in “Opening the door in the event of a
blocked drain outlet and/or power failure”.

The water level in the drum is too high.

Cancel the programme. The water will be pumped
away.

Comfort cooling

appears in the display
after a programme has
been cancelled.

For safety reasons the drum door cannot be opened if
the suds temperature is higher than 55 °C.

Wait until the temperature in the drum has
decreased and the message has gone out in the
display.

The following appears
in the display:

 

 Service Door release

The door lock has jammed.

Call the Service Department.

Summary of Contents for WKG 120 WCS





































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands