manualshive.com logo in svg

Miele WKG 120 WCS, Operating Instructions Manual

Share
Download
Miele WKG 120 WCS Operating Instructions Manual Download Page 17

Before using for the first time

17

Remove the detergent
cartridges and the drain hose
elbow from the drum

Two detergent cartridges for automatic
detergent dispensing and an elbow
piece for the drain hose are stored in
the drum.

Reach under the door grip and pull
the door open.

Take the two cartridges and the
elbow piece out of the drum.

Shut the door with a gentle swing.

Inserting detergent cartridges

The detergent cartridges removed from
the drum are components of the Miele 2
phase system consisting of:

1. UltraPhase 1 (base detergent)

2. UltraPhase 2 (detergent enhancer)

The detergent cartridges are single
use products. New detergent
cartridges can be obtained from the
Miele online shop or directly from
Miele (see the end of this booklet for
details). Empty cartridges should be
disposed of via your local recycling
system 

.

Remove the foil or the stoppers from
the detergent cartridges.

Summary of Contents for WKG 120 WCS





































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands