manualshive.com logo in svg

Miele WKG 120 WCS, Operating Instructions Manual

Share
Download
Miele WKG 120 WCS Operating Instructions Manual Download Page 62

Problem solving guide

62

A message about the TwinDos System has appeared in the
display

Message

Cause and remedy

Cartridge  almost
empty

The detergent in the cartridges is running low. There
are between 4 and 8 wash cycles remaining.

Order new cartridges.

Container  empty

The cartridges or TwinDos containers are empty.

Replace the cartridges or refill the TwinDos
containers.

Check whether the laundry is clean. If it is not
there may not have been enough detergent. 
If necessary, wash the items again.

Use "TwinDos" or
start Maintenance.
See 

TwinDos or automatic dispensing via compartment 

and/or 

 has not been used for a long time.

Use TwinDos for one of your next loads.

Carry out the TwinDos maintenance programme as
described in “Cleaning and care”, “TwinDos
maintenance”.

TwinDos Maint. for
compart.  and 
must be started. See

TwinDos or automatic dispensing via compartment 

and/or 

 has not been used for a long time. It is

possible that detergent has dried inside the hoses.

Carry out the TwinDos maintenance programme

immediately

 as described in “Cleaning and care”,

“TwinDos maintenance”.

The messages shown on this page are examples. They may differ depending on
whether they refer to compartment 

 or 

.

The messages will appear at the end of the programme and when the washing
machine is switched on and need to be confirmed with the 

OK

 sensor.

Summary of Contents for WKG 120 WCS





































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands