Miele W 3834 WPS Operating Instructions Manual Download Page 28

Page: 28 / 68

System lock

The system lock prevents your
machine being used without your
knowledge.

If the system lock has been activated it
is not possible to start a programme.

To activate the system lock

Before you begin, first ensure that:

– The washing machine is switched off.

– The drum door is closed

Press the

Water plus

and

Temperature

buttons at the same

time and hold them pressed in until
you reach step

Switch the machine on with the

I-On/

0-Off

button.

Press the

Degree of soiling light/

normal/heavy

button three times.

Then release the

Water Plus

and

Temperature

buttons.

The

Locked

check light will flash.

Switch off the washing machine.

To deactivate the system lock

Repeat steps

. The

Locked

check light will go out.

Changing the programme sequence

Summary of Contents for W 3834 WPS





































































Search results

Summary of Contents for W 3834 WPS

Reviews:

Related manuals for W 3834 WPS

Brands by name

Popular brands

Miele W 3834 WPS, Operating Instructions Manual

Search results

Summary of Contents for W 3834 WPS

Reviews:

Related manuals for W 3834 WPS

Brands by name

Popular brands