Miele W 3834 WPS Operating Instructions Manual Download Page 10

Page: 10 / 68

Control panel

Programme buttons

For selecting a washing programme.

Soiling button

For specifying the degree of soiling
of the laundry.

Water plus button

For increasing the water level.

Temperature button

For selecting a temperature.

Spin speed button

For selecting a final spin speed.

PC / Optical interface

This is used by service technicians
to run diagnostic checks on your
machine and can also be used to
update programming data in the
future.

Sequence indicator lights

Show which section of the wash
programme has been reached.

Buzzer button

Check lights

Delay start button

For delaying the start of a
programme.

Start/Stop button

For starting the programme selected
and cancelling a programme once it
has started.

I-On/0-Off button

For switching the machine on or off.

Door button

Opens the machine door.

Display (h min)

The display fulfills several functions.
See next page for details.

Description of the machine

Summary of Contents for W 3834 WPS





































































Search results

Summary of Contents for W 3834 WPS

Reviews:

Related manuals for W 3834 WPS

Brands by name

Popular brands

Miele W 3834 WPS, Operating Instructions Manual

Search results

Summary of Contents for W 3834 WPS

Reviews:

Related manuals for W 3834 WPS

Brands by name

Popular brands