Miele W 3834 WPS Operating Instructions Manual Download

Page: 16 / 68

Specify the degree of soiling of the
laundry

Press the top button to select the
degree of soiling.

Normal

is the default

setting.

Use the lower button to select the

Water

plus

option.

Press the top button repeatedly until
the degree of soiling you want lights
up.

Press the

Water plus

button if you

want to activate this function.

You cannot select the degree of soiling
or

Water plus

for every programme.

You can change the pre-set
temperature or spin speed by pressing
the

Temperature

Spin

button.

In some programmes the maximum
temperature and spin speed is limited.
The machine will not allow a higher
value to be selected.

Press the

Temperature

Spin

button

repeatedly until the indicator light for
the value you want comes on.

Press the

Buzzer

button if you want to

be reminded when the programme is
finished.

How to wash correctly

Summary of Contents for W 3834 WPS





































































Search results

Summary of Contents for W 3834 WPS

Reviews:

Related manuals for W 3834 WPS

Brands by name

Popular brands

Miele W 3834 WPS, Operating Instructions Manual

Search results

Summary of Contents for W 3834 WPS

Reviews:

Related manuals for W 3834 WPS

Brands by name

Popular brands