Miele PWM 507 Hygiene Operating And Installation Instructions Download Page 36

Page: 36 / 92

Programme chart



Minimum iron

30 °C to 40 °C

Max. load 3.5 kg

Use for

Synthetic and mixed fibre textiles and easy care cotton

Tip

– Reduce the spin speed for fabric that creases easily.

1200 rpm

Extras: Pre-wash



, Pre-ironing



Rinses: 2–4*



Delicates

30 °C

Max. load 2.5 kg

Use for

Delicate garments made from synthetic fibre, mixed fibre and vis-
cose

Tip

– Deselect the spin speed for fabric that creases easily.

600 rpm

Extras: Pre-wash



, Pre-ironing



Rinses: 2





Drain/Spin

Max. load 7.0 kg

Tip

– Make sure you select the appropriate spin speed.

– Select the

Rinse plus

Extra for an additional rinse.

– Drain only: select 0 rpm for the spin speed.

1600 rpm

Extras: Rinse plus



* You can alter the number of rinses carried out via the Supervisor level.

Summary of Contents for PWM 507 Hygiene





























































































Search results

Summary of Contents for PWM 507 Hygiene

Reviews:

Related manuals for PWM 507 Hygiene

Brands by name

Popular brands

Miele PWM 507 Hygiene, Operating And Installation Instructions

Search results

Summary of Contents for PWM 507 Hygiene

Reviews:

Related manuals for PWM 507 Hygiene

Brands by name

Popular brands