Miele PWM 507 Hygiene Operating And Installation Instructions Download Page 26

Page: 26 / 92

3. Selecting a programme

Switching on the washing ma-
chine



Press the



control.

The interior drum lighting will come on.

The drum lighting will go out automat-
ically after five minutes or when the
programme starts.

Selecting a programme

Select standard programmes with
the programme selector dial



Turn the programme selector to the
required programme.

The selected programme will be shown
in the display. The display will then
change to the main menu for that pro-
gramme.

Select special programmes via the



programme selector position



Turn the programme selector to the



position.

You can select the required programme
via the display.



Special

progs.





Sportswear

SportMicrofibre



Touch the





sensor until the

programme you want appears in the
display.



Touch the sensor for that programme.

The display will change to the main
menu for that programme.

Summary of Contents for PWM 507 Hygiene





























































































Search results

Summary of Contents for PWM 507 Hygiene

Reviews:

Related manuals for PWM 507 Hygiene

Brands by name

Popular brands

Miele PWM 507 Hygiene, Operating And Installation Instructions

Search results

Summary of Contents for PWM 507 Hygiene

Reviews:

Related manuals for PWM 507 Hygiene

Brands by name

Popular brands