Miele PW 6065 Operating Manual Download Page 28

Page: 28 / 72

The washer has the option to save the most used wash
programs on the direct select buttons. The option "Save"
must be selected in the "Settings - Supervisor level".
Contact Technical Service for access to this level.

Selecting/Changing a Favorite

Main menu

1 Cottons Uni.

140°F

Program selection

2 Minimum iron

104°F

Settings

3 Delicates

104°F

4 Woollens

86°F

12:00

Press the direct select button

Basic menu

Cottons Uni.

140°F

1400 rpm

Duration 0:45 h

Extras

Delay Start

Save

Back

Turn the jog shuttle to select the component you want to
adjust: program, temperature or spin speed.

Press the jog shuttle to confirm the selection.

Depending on the selection the display shows one of the following
submenus.

Important: If no selection is made in the sub-menu, the
display will switch back to the basic menu after 20
seconds.

– Select a program

Program

Back

selection

Cottons Hygiene

Cottons Uni.

Minimum iron

Select the desired program with the jog shuttle and
confirm. The basic menu shows again.

Favorites

Summary of Contents for PW 6065









































































Search results

Summary of Contents for PW 6065

Reviews:

Related manuals for PW 6065

Brands by name

Popular brands

Miele PW 6065, Operating Manual

Search results

Summary of Contents for PW 6065

Reviews:

Related manuals for PW 6065

Brands by name

Popular brands