Miele PW 6065 Operating Manual Download Page 26 | Manualshive

Page: 26 / 72

background image

Rinse Stop

The washer stops after the last rinse, the laundry remains
soaking in water. This will prevent wrinkles if the laundry is not
removed immediately at the end of the wash program.

Intensive*

For laundry with normal to heavy soiling or stains.

The total time for the wash program will be extended.

Water plus*

The washer comes factory set with the Extra selection "Water
plus" activated. The water level during washing and rinsing is
increased.

Other settings for "Water plus" can be selected. See "Settings"
for more information.

* "Intensive" and "Water plus" can be added from the "Settings
- Supervisor level" menu, when the access is activated by

Technical Service.

Extras which can be selected are shown in the sub-menu
"Extras". If an Extra is not shown, it is not available for the
selected program.

Options

26

«
...
24
25
26
27
28
...
»

Summary of Contents for PW 6065









































































Reviews:

No comments

Related manuals for PW 6065

Brand: GE Pages: 108

Brand: Haier Pages: 12

Brand: DAEWOO ELECTRONICS Pages: 28

Brand: Landa Pages: 44

Brand: Kärcher Pages: 24

Brand: Parmco Pages: 22

Brand: JUNO Pages: 25

Brand: Tricity Bendix Pages: 28

Brand: Hoover Pages: 17

AQUALTIS AQLF8F 292 U

Brand: Hotpoint Ariston Pages: 64

Brand: Kranzle Pages: 18

Brand: arcelik Pages: 32

Brand: Asko Pages: 24

Brand: Hotpoint Pages: 16

Brand: Lavorwash Pages: 12

Brand: Kärcher Pages: 232

Brand: Maytag Pages: 36

Brand: LVO Manufacturing Pages: 34

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands