Miele PW 6065 Operating Manual Download Page 18

Page: 18 / 72

Woollens 104°F to cold (40°C to cold)

Items

Items made from machine washable wool and wool blend
fabrics.

Detergent

Detergent for wool

Load size

5.5 lbs (2.5 kg)

Silk

86°F to cold (30°C to cold)

Items

Hand washable items, that contain no wool.

Tip

Wash hosiery and lingerie in a lingerie bag.

Detergent

Detergent for delicates

Load size

5.5 lbs (2.5 kg)

Shirts 140°F to cold (60°C to cold)

Items

Shirts and dress shirts.

Tip

–

Pre-treat collars and cuffs depending on soiling

–

Wash silk shirts in the "Silk" program.

Detergent

Universal or color detergent

Load size

5.5 lbs (2.5 kg)

Denim 104°F to cold (40°C to cold)

Tip

–

Before washing denim items turn them inside out.

–

Denim items bleed at the first few washes. Wash dark and
light colored items separately.

Detergent

Liquid color detergent

Load size

7.7 lbs (3.5 kg)

Towelling 203°F to 140°F (95°C to 60°C)

Tip

Use color detergent for dark colored laundry

Detergent

Universal detergent

Load size

12.1 lbs (5.5 kg)

Drain

To drain the water from the drum

Spin

Please select an appropriate spin speed

Program guide

Summary of Contents for PW 6065









































































Search results

Summary of Contents for PW 6065

Reviews:

Related manuals for PW 6065

Brands by name

Popular brands

Miele PW 6065, Operating Manual

Search results

Summary of Contents for PW 6065

Reviews:

Related manuals for PW 6065

Brands by name

Popular brands