Miele PW 6065 Operating Manual Download Page 20

Page: 20 / 72

Outerwear 104°F to cold (40°C to cold)

Items

Outdoor clothing made from micro fibers.

Tip

–

Close all zippers.

–

Do not use fabric softener

Detergent

Detergent for delicates

Load size

7.7 lbs (3.5 kg)

Proofing 104°F to 86°F (40°C to 30°C)

Items

To treat micro fiber, ski clothing, fine dense cotton (poplin) or table
cloths to make them water repellent and soil resistant.

Tip

–

The item should be washed and rinsed or dried.

–

To get an optimum result dry the items in a clothes dryer or iron
them.

Water
repellent

–

Only use water repellent that states it is "Suitable for membrane
textiles". They are based on fluorochemicals.

Do not use

agents containing paraffin.

–

Place the liquid detergent insert in compartment

an fill with

water repellent.

Load size

7.7 lbs (3.5 kg)

Program guide

Summary of Contents for PW 6065









































































Search results

Summary of Contents for PW 6065

Reviews:

Related manuals for PW 6065

Brands by name

Popular brands

Miele PW 6065, Operating Manual

Search results

Summary of Contents for PW 6065

Reviews:

Related manuals for PW 6065

Brands by name

Popular brands