Miele PW 6065 Operating Manual Download Page 54 | Manualshive

Page: 54 / 72

background image

Hot water connection

Connecting the machine to a hot water
supply will lead to low electrical
consumption during hot water
operation. The hot water temperature at
the water faucet must not exceed 158°F
(70°C).
The water in single water lines from the
hot water source cools faster when not
in constant use. To heat the wash water
more electricity must be used. The
same conditions for the hot water as for
the cold water connection will then
apply.

^

Connect the hot water intake hose
(red mark) to the water faucet.

The connection of the machine to a
hot water line only, is not possible for
functional reasons.

If the washer is not to be installed for
hot water connection, the settings "Main
wash", "Pre-wash" and "Rinse" must be
adjusted respectively. The hot water
intake hose must be removed.

^

Select in "Settings - Supervisor level"
the respective options "cold".

The program times may be
extended.

^

Unscrew the hot water intake hose
(red mark).

^

Screw on the supplied stopper.

Installation

54

«
...
52
53
54
55
56
...
»

Summary of Contents for PW 6065









































































Reviews:

No comments

Related manuals for PW 6065

Brand: Haier Pages: 6

Brand: Haier Pages: 6

Brand: Haier Pages: 24

Brand: Haier Pages: 12

Brand: Haier Pages: 12

Brand: Haier Pages: 23

Brand: Haier Pages: 12

Brand: Kärcher Pages: 24

Brand: Foamit Pages: 6

Brand: Dawlance Pages: 44

ODW 60032 FS A2

Brand: OK. Pages: 27

Brand: Hypro Pages: 20

Brand: Hotpoint Pages: 2

Brand: Zanussi Electrolux Pages: 24

Brand: Gorenje Pages: 24

Brand: BE Pages: 32

Brand: CaterChef Pages: 44

Brand: Porter-Cable Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands