Miele PW 6065 Operating Manual Download Page 63

Page: 63 / 72

Standby

The display goes out after 10
minutes and the "Start" button
flashes slowly to save energy.

The display will go into Standby mode:

– if no program was selected after the

machine was turned on.

– after a program has started.

– at the end of a program.

Not in current prog.
(Factory default)

The Standby function will be turned on
if no program was selected after the
machine was turned on.

By turning the jog shuttle or pressing
any button the display is turned on
again.

Memory

The Memory function remembers the
addition of an extra feature to a
program, a change in spin speed or
the temperature the next time that
program is selected.

Once the wash program is selected
again the washer shows the saved
options.

The memory function is not active when
favorites are selected with the direct
select buttons.

The Memory function is factory set "off".

Temperature unit

The temperature can be shown in
"°C/Celsius" (factory default) or
"°F/Fahrenheit".

The delivery status is "°C".

Settings

Summary of Contents for PW 6065









































































Search results

Summary of Contents for PW 6065

Reviews:

Related manuals for PW 6065

Brands by name

Popular brands

Miele PW 6065, Operating Manual

Search results

Summary of Contents for PW 6065

Reviews:

Related manuals for PW 6065

Brands by name

Popular brands