Miele PW 6065 Operating Manual Download Page 11

Page: 11 / 72

The appliance must be correctly
installed and connected before the
first use. Please see the "Installation
instructions."

For safety reasons, it is not possible to
run a spin cycle before the first use. A
program must be run

without laundry

and detergent

to flush out any residual

water from the factory testing process.

Open the water mains.

Welcome screen

The Welcome screen shows when the
washer is turned on for the first time.

PROFESSIONAL

Welcome!

The welcome screen will not show
anymore, when the total wash time of
the washer exceeds one hour.

The display then shows the language
selection.

Language

Select the desired language and
confirm with "OK".

Shipping struts

The display reminds the user to remove
the shipping struts.

If the shipping struts were already
removed, confirm with the

button. Otherwise remove them at
this time then confirm.

Set the time of day

Set the hour by turning the jog shuttle
and press to confirm.

Repeat to set the minutes and
confirm. Press again to save the time
of day.

Basic menu "Cottons Uni." shows

Press the flashing button "Start".
The drum door must be closed.

Once the program ends the washer can
be used for laundry.

Before using for the first time

Summary of Contents for PW 6065









































































Search results

Summary of Contents for PW 6065

Reviews:

Related manuals for PW 6065

Brands by name

Popular brands

Miele PW 6065, Operating Manual

Search results

Summary of Contents for PW 6065

Reviews:

Related manuals for PW 6065

Brands by name

Popular brands