Miele KFN 37432 iD Operating And Installation Instructions Download Page 61 | Manualshive

Page: 61 / 104

background image

Cleaning and care

61

Replacing the charcoal filters

Charcoal filters and a KKF-FF (Active
AirClean) holder are available as
optional accessories (see
“Accessories - optional accessories”).

Replace the charcoal filters in the
holder every 6 months.

Replacement KKF-RF charcoal filters
can be obtained from Miele, from your
dealer or from Miele's website.

Tip:

The charcoal filter holder is

dishwasher-proof.



Pull the charcoal filter holder upwards
to remove it from the shelf.

When in position, the charcoal filters
must not touch the back wall of the
appliance as the moisture could
cause them to stick to the back wall.
Insert the new charcoal filters into
the holder so that they do not
protrude over the edge of the holder.



Remove both charcoal filters and
place the new filters with the framed
edge pointing downwards in the
holder.



Place the holder in the middle of the
raised edge at the back of the shelf,
so that it clicks into position.

«
...
59
60
61
62
63
...
»

Summary of Contents for KFN 37432 iD









































































































Reviews:

No comments

Related manuals for KFN 37432 iD

Brand: Lacor Pages: 80

Brand: Traulsen Pages: 16

Brand: ICELAND Pages: 24

MyDrink Drinkmaster

Brand: Waeco Pages: 36

Brand: ZANKER Pages: 36

Brand: Daewoo Pages: 63

Brand: Hotpoint Pages: 12

Brand: VALERA Pages: 2

Brand: Hanseatic Pages: 60

Brand: Beko Pages: 27

Brand: Beko Pages: 33

Brand: Beko Pages: 25

Brand: Beko Pages: 24

Brand: Beko Pages: 69

Brand: Beko Pages: 20

Brand: Beko Pages: 28

Brand: Beko Pages: 20

Brand: Beko Pages: 11

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands