Miele KFN 37432 iD Operating And Installation Instructions Download Page 58

Page: 58 / 104

Cleaning and care



Grasp the plastic surround on the
left-hand side of the stainless steel
trim at its rearmost point.

1. Pull the plastic surround from the

adjustable shelf and

2. pull the trim off at the same time. The

opposite side will also be released.

3. Then pull the protective strip off.



After cleaning, reattach the stainless
steel trim or protective strip by
following the same procedure in
reverse.

Dismantling the bottle and door
shelves

Remove the stainless steel trim before
cleaning the door shelves in a
dishwasher.

To remove the stainless steel trim,
proceed as follows:



Place the door/bottle shelf with the
front side on the work surface.



Take hold of one end of the trim and
pull it off the shelf. The entire section
of stainless steel trim will now come
off the shelf.



After cleaning, reattach the stainless
steel trim to the shelf by following the
same procedure in reverse.

Summary of Contents for KFN 37432 iD









































































































Search results

Summary of Contents for KFN 37432 iD

Reviews:

Related manuals for KFN 37432 iD

Brands by name

Popular brands

Miele KFN 37432 iD, Operating And Installation Instructions

Search results

Summary of Contents for KFN 37432 iD

Reviews:

Related manuals for KFN 37432 iD

Brands by name

Popular brands