Miele KFN 37432 iD Operating And Installation Instructions Download Page 36

Page: 36 / 104

Selecting further settings

Certain settings on the appliance can
only be selected in settings mode.

When in settings mode, the door
alarm and other fault messages are
automatically deactivated although the
alarm symbol



appears in the

display.

Settings options



Activating or deactivating the
lock



Switching the audible signals
on/off



Altering the display brightness



Switching Sabbath mode on/off



Activating the charcoal filter
replacement indicator or
resetting the counter

All of these settings options are
described below.

Safety lock



The safety lock can be activated to
prevent:

– The appliance being switched off by

mistake

– The temperature being changed by

mistake

– The DynaCool, SuperCool and

SuperFreeze functions being selected
by mistake

– Settings being adjusted by mistake (it

is only possible to deactivate the
safety lock)

This prevents the appliance being
switched off or settings being adjusted
without your knowledge (by children, for
example).

Activating or deactivating the safety
lock



Touch the settings sensor.

All symbols available for selection will
appear in the display and the



symbol

flashes.



Touch the OK sensor to confirm your
selection.

The last selected setting flashes and
the



symbol lights up in the display.

Summary of Contents for KFN 37432 iD









































































































Search results

Summary of Contents for KFN 37432 iD

Reviews:

Related manuals for KFN 37432 iD

Brands by name

Popular brands

Miele KFN 37432 iD, Operating And Installation Instructions

Search results

Summary of Contents for KFN 37432 iD

Reviews:

Related manuals for KFN 37432 iD

Brands by name

Popular brands