Miele KFN 37432 iD Operating And Installation Instructions Download Page 60

Page: 60 / 104

Cleaning and care

Cleaning the door seal



Risk of damage as a result of

incorrect cleaning.
If you treat the door seal with oils or
grease, it can become porous.
Do not use any oils or grease on the
door seal.



The door seal should be cleaned
regularly with clean water and then
wiped dry with a cloth.

Cleaning the ventilation gaps

A build-up of dust will increase the
energy consumption of the appliance.



The ventilation gaps should be
cleaned on a regular basis with a
brush or vacuum cleaner (e.g. use the
dusting brush for Miele vacuum
cleaners)

After cleaning



Replace all shelves and accessories
in the appliance.



Reconnect to the mains and switch
the appliance back on.



Switch on the Super freeze function
for a while so that the freezer section
can cool down quickly.



Switch on the Super cool function for
a while so that the refrigerator section
can cool down quickly.



Place food in the refrigerator section
and close the door.



Place the freezer drawers with the
frozen food back in the freezer
section and close the door.



When the temperature in the freezer
section is a constant -18 °C or colder
press the Super freeze button to
switch the Super freeze function off.

Summary of Contents for KFN 37432 iD









































































































Search results

Summary of Contents for KFN 37432 iD

Reviews:

Related manuals for KFN 37432 iD

Brands by name

Popular brands

Miele KFN 37432 iD, Operating And Installation Instructions

Search results

Summary of Contents for KFN 37432 iD

Reviews:

Related manuals for KFN 37432 iD

Brands by name

Popular brands