Miele KFN 37432 iD Operating And Installation Instructions Download Page 27

Page: 27 / 104

The correct temperature

Temperature display

In normal operation the display shows
the

average, current temperature in

the refrigerator section

and the

temperature

in the warmest area of

the freezer section

If the temperature in the freezer section
is not within the normal temperature
display range, dashes will flash in the
display.

Depending on the ambient temperature
and the temperature setting, it can take
the appliance a few hours to reach the
temperature required and for this
temperature to then be shown as a
constant temperature in the display.

Setting the temperature in the
refrigerator / freezer sections

The temperatures for the refrigerator
and freezer sections are set
independently of one another.



Select the refrigerator or the freezer
section.



Use the two sensors underneath the
display to set the temperature.

By touching the sensor

– the temperature will get colder

– the temperature will get warmer.

The temperature being set will flash in
the display.

Summary of Contents for KFN 37432 iD









































































































Search results

Summary of Contents for KFN 37432 iD

Reviews:

Related manuals for KFN 37432 iD

Brands by name

Popular brands

Miele KFN 37432 iD, Operating And Installation Instructions

Search results

Summary of Contents for KFN 37432 iD

Reviews:

Related manuals for KFN 37432 iD

Brands by name

Popular brands