Miele KFN 37432 iD Operating And Installation Instructions Download Page 29

Page: 29 / 104

Using Super cool, Super freeze and Dynamic cooling

Super cool function

The Super cool function can be used to
rapidly reduce the temperature in the
refrigerator section to its lowest setting
(depending on the room temperature).

Switching on Super cool

Super cool is particularly recommended
for the rapid chilling of large amounts of
fresh food or drink.



Touch the sensor for the refrigerator
section.

The symbol for the refrigerator section
is highlighted in yellow.



Touch the Super cool sensor so that
it is highlighted in yellow.

The appliance will work at full power to
lower the temperature in the refrigerator
section.

Switching off Super cool

The Super cool function switches off
automatically after approx. 12 hours.
The appliance will then continue to
work at normal power.

To save energy, the Super cool function
can be switched off once food and
drinks are sufficiently chilled.



Touch the sensor for the refrigerator
section.

The symbol for the refrigerator section
is highlighted in yellow.



Touch the Super cool sensor so that
it is no longer highlighted in yellow.

The appliance will continue running at
normal power.

Summary of Contents for KFN 37432 iD









































































































Search results

Summary of Contents for KFN 37432 iD

Reviews:

Related manuals for KFN 37432 iD

Brands by name

Popular brands

Miele KFN 37432 iD, Operating And Installation Instructions

Search results

Summary of Contents for KFN 37432 iD

Reviews:

Related manuals for KFN 37432 iD

Brands by name

Popular brands