Miele KF 1803 SF Page 77 Operating And Installation Instructions Download

Page: 77 / 84

Preparing the water connection

The connection to the household
water supply must be installed
before the appliance is installed.

Turn off the main water valve to prevent
damage caused by leaking water.

Attach the connecting pipe to the
shut-off valve, according to the
instructions supplied by the
manufacturer of the ice cube maker
installation kit.

Install the connecting pipe. Always
observe the indicated clearance
dimensions to prevent damage to the
connecting pipe when pushing in the
appliance.

Secure the connecting pipe to the
floor with adhesive tape.

You may now proceed to install the
appliance. See "Installing the
appliance".

For appliances with a hose guide

position the device in front of the
niche and push the stainless steel
tube through the hose guide at the
back of the unit.

At this point the niche should be ready
for the appliance to be pushed back
into it (see "Installing the appliance").

You can now continue with the
installation.

Plumbing

Summary of Contents for KF 1803 SF





















































































Search results

Summary of Contents for KF 1803 SF

Reviews:

Related manuals for KF 1803 SF

Brands by name

Popular brands

Miele KF 1803 SF, Operating And Installation Instructions

Search results

Summary of Contents for KF 1803 SF

Reviews:

Related manuals for KF 1803 SF

Brands by name

Popular brands