Miele KF 1803 SF Page 57 Operating And Installation Instructions Download

Page: 57 / 84

Stainless steel panels

Stainless steel door panels and toe-kick
covers are available from Miele.

Installation options

There are many different installation
options. You are limited only by the
design of the kitchen.

The door hinge cannot be
exchanged.

Single column

The appliance can be installed at any
preferred location in the kitchen.

However, be sure the door will open
and close properly in the chosen
location.

Side-by-side

This appliance can be installed
"side-by-side" with another
fridge/freezer using a "Merging Kit".

The "Merging Kit" is available from
Miele.

Contact Miele or your dealer for
specific information about which
combinations will work with your
appliance.

For instructions on how to attach the
appliances and install the heating
mat, please refer to the instructions
included with the "Merging Kit",
available from Miele.

Appliances attached together using
the "Merging Kit"

If the appliances are installed directly
next to each other (without a partition),
they need to be attached together
using the "Merging Kit".

Installation

Summary of Contents for KF 1803 SF





















































































Search results

Summary of Contents for KF 1803 SF

Reviews:

Related manuals for KF 1803 SF

Brands by name

Popular brands

Miele KF 1803 SF, Operating And Installation Instructions

Search results

Summary of Contents for KF 1803 SF

Reviews:

Related manuals for KF 1803 SF

Brands by name

Popular brands