Miele KF 1803 SF Page 38 Operating And Installation Instructions Download

Page: 38 / 84

After the filter change the filter
indicator in the display still flashes.
The change must be be confirmed in
the electronic.

Confirming the filter change

Press and hold the filter change
sensor button.

At the same time place a finger on
the access button. Press and hold
both sensor buttons for approx. 5
seconds until a beep is heard.

The water filter change has been
confirmed and the filter change
indicator had been reset.

The filter change indicator goes out.

Close the door.

After installing a new water filter
discard the first 24 hours of ice
production.

Using an external water filter

If your household water supply already
has an external water filter installed,
leave the standard water filter (bypass
cartridge) installed in the appliance.

Water filter

Summary of Contents for KF 1803 SF





















































































Search results

Summary of Contents for KF 1803 SF

Reviews:

Related manuals for KF 1803 SF

Brands by name

Popular brands

Miele KF 1803 SF, Operating And Installation Instructions

Search results

Summary of Contents for KF 1803 SF

Reviews:

Related manuals for KF 1803 SF

Brands by name

Popular brands