Miele G 811 Operating Instructions Manual Download Page 6

Page: 6 / 60

IMPORTANT SAFETY INSTRUCTIONS

WARNING

Please follow all basic safety
precautions when operating
this dishwasher.

This appliance conforms with
all uniform safety codes and
regulations. To avoid injury
and machine damage, read
the operating instructions
carefully.

The manufacturer cannot be held
responsible for damage or injury
caused by improper use or for uses
other than those for which the appli-
ance is intended.

Repairs should only be performed
by a qualified and competent per-

son. Disconnect the appliance from the
power supply before servicing (pull out
the plug or “trip” the circuit breaker).

This dishwasher should only be in-
stalled under a continuous

countertop secured to adjacent
cabinetry.

The dishwasher must be electri-
cally grounded. Install the dish-

washer as outlined in the included In-
stallation instructions.

Only use detergents and rinse aids
recommended for residential dish-

washers.

Do not use the dishwasher unless
all panels are in place.

Do not allow children to play in or
on the dishwasher.

Keep all detergents and rinse aids
out of the reach of children.

Dishwasher detergents contain
Sodium Silicate and Sodium

Carbonate. In case of eye contact,
immediately flush with water.
Call a physician or poison control.

Do not tamper with the
controls.

Do not drink water from the dish-
washer.

IMPORTANT SAFETY INSTRUCTIONS

Summary of Contents for G 811





























































Search results

Summary of Contents for G 811

Reviews:

Related manuals for G 811

Brands by name

Popular brands

Miele G 811, Operating Instructions Manual

Search results

Summary of Contents for G 811

Reviews:

Related manuals for G 811

Brands by name

Popular brands