Miele G 811 Operating Instructions Manual Download Page 36 | Manualshive

Page: 36 / 60

background image

Cleaning and care

Cleaning the filters in the wash
cabinet

The combination filter in the base of the
wash cabinet should be regularly in-
spected and cleaned, every 4 - 6
months. Any broken glass or dishware
should be removed immediately.

Use caution when cleaning the
filters, non-return valve or drain
pump; glass or bone splinters
may be caught in the bottom of
the wash cabinet.

^

Turn off the dishwasher.

^

Turn the handle counterclockwise to
release the filters.

^

Lift the combination filter out of the
machine. Remove any coarse parti-
cles and rinse under running water.
A nylon brush can be used.

Cleaning and care

36

«
...
34
35
36
37
38
...
»

Summary of Contents for G 811





























































Reviews:

No comments

Related manuals for G 811

Brand: GE Pages: 2

Brand: Daewoo Pages: 17

Brand: Daewoo Pages: 16

Brand: VOX electronics Pages: 154

Brand: Estate Pages: 1

Brand: Maidaid Halcyon Pages: 17

ODW 60032 FS A2

Brand: OK. Pages: 27

Conservator 3955874A

Brand: Crosley Pages: 8

Brand: SPT Pages: 21

AdorinaWaschen V600

Brand: V-ZUG Pages: 20

Brand: Sandstrom Pages: 36

Brand: Proline Pages: 86

Brand: ZANKER Pages: 17

Brand: Daewoo Pages: 7

Brand: NEFF Pages: 56

Brand: NEFF Pages: 60

Brand: NEFF Pages: 60

Brand: NEFF Pages: 56

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands