Miele G 811 Operating Instructions Manual Download Page 32 | Manualshive

Page: 32 / 60

background image

Interrupting a program

A program is interrupted as soon as the
door is opened.
If the door is closed again, the program
will continue from the point it was at be-
fore the door was opened.

Warning:
Water in the dishwasher may be
hot. There is a danger of being
burned!
Only open the door if absolutely
necessary and with caution. Be-
fore closing the door, leave it
open for approximately 20 sec-
onds. This will allow the tempera-
ture in the wash cabinet to settle.
Close the door firmly until it clicks
into place.

Changing a program

If a program has already started and
you wish to change it proceed as fol-
lows:

^

Turn the program selector (17) to the
“Stop” position.

^

Leave the program selector (17) in
this position for at least one second.

^

Then turn the program selector (17)
to the program you wish to use.

^

Press the “Start” button (18).

The program starts.

Operating the dishwasher

32

«
...
30
31
32
33
34
...
»

Summary of Contents for G 811





























































Reviews:

No comments

Related manuals for G 811

Brand: NEFF Pages: 2

Brand: NEFF Pages: 2

Brand: NEFF Pages: 2

Brand: Gorenje Pages: 18

Brand: Gibson Pages: 14

Brand: Maidaid Halcyon Pages: 17

Brand: Gaggenau Pages: 32

Brand: Gaggenau Pages: 68

CF 1201 - 3 PHASE

Brand: VALERA Pages: 2

Brand: Maytag Pages: 56

Brand: P&C Pages: 45

Brand: Daewoo Pages: 26

Brand: CDA Pages: 40

Brand: Belling Pages: 24

Brand: Ardo Pages: 14

Brand: HomeKing Pages: 52

Brand: FAR Pages: 155

Brand: V-ZUG Pages: 52

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands