Miele G 7881 Installation And Operating Instructions Manual Download Page 74

Page: 74 / 76

Choose your program according to the types of instruments or utensils being
cleaned and the degree of soiling.

Programs

(fixed)

Program Description

Wash

Wash program without disinfection.

Rinse (cold)

Rinse only.
To rinse items before a wash program, to avoid excessive
foam.

Drain

For draining water out of the machine, e.g. when a program
has been interrupted or the "Fill/Drain" indicator illuminates.
(Turn the program selector to the "Stop"

position first).

Disinfection
vario

Recommended program for protein soils such as blood and
tissue. For cleaning and thermal disinfection at 93

C with 10

minutes holding time for stainless steel instruments.

Disinfection
93°C-10’

For thermal disinfection and cleaning of stainless steel
instruments at 93

C with 10 minutes holding time.

Program guide

Summary of Contents for G 7881













































































Search results

Summary of Contents for G 7881

Reviews:

Related manuals for G 7881

Brands by name

Popular brands

Miele G 7881, Installation And Operating Instructions Manual

Search results

Summary of Contents for G 7881

Reviews:

Related manuals for G 7881

Brands by name

Popular brands