Miele G 7881 Installation And Operating Instructions Manual Download Page 41

Page: 41 / 76

Priming the liquid detergent dispensing system

The dispensing system does not need to be primed (cleared of air) unless:
– the dispensing concentration is being set for the first time,
– the liquid detergent container was not refilled in time and became completely

empty.

Step

Display / Result

Activate the programming mode as per
page 35.

Press the "Drying"

button until E02

appears in the display.

E02

Turn the program selector to the 1 o'clock
position.

d§1

Press the "Display"

button.

The dispensing system will be
primed automatically. Priming is
complete when

appears in the

display.

Save to memory and exit programming
mode as per page 35.

Select the "Rinse" program and "Start"

button to run a rinse cycle.

This will rinse away any agents that
entered the wash cabinet after
priming.

Programmable functions

Summary of Contents for G 7881













































































Search results

Summary of Contents for G 7881

Reviews:

Related manuals for G 7881

Brands by name

Popular brands

Miele G 7881, Installation And Operating Instructions Manual

Search results

Summary of Contents for G 7881

Reviews:

Related manuals for G 7881

Brands by name

Popular brands