Miele G 6993 Operating Instructions Manual Download Page 97 | Manualshive

Page: 97 / 104

background image

Settings menu

97

Memory

With the Memory function activated, the
dishwasher will save the last
programme that was run.
When you switch the dishwasher off
and back on again, the last programme
used will appear in the display instead
of the

ECO

programme.



Select the setting you want and
confirm with

OK

.

Refill reminders

If you only ever use combination
products containing salt and rinse aid in
your dishwasher, you can switch the
reminders for salt and rinse aid off if
you wish (see "Settings menu, Refill
reminders"). Switching off the reminders
will not affect the DetergentAgent
function (see "Programme options,
DetergentAgent").



Select the setting you want and
confirm with

OK

.

If you switch to using detergent that
does not contain salt or rinse aid, it
is important to remember to add salt
and rinse aid and to switch the
reminders back on.

Check filters

You can adjust the interval at which the
reminder to check the filters appears.
You can set an interval of between 30
and 60 programme cycles.

The reminder to check the filters is set
at the factory to appear after every 50
programme cycles.



Select the interval you want and
confirm with

OK

.

Automatic

You can adjust the

Automatic

programme so that it will remove
stubborn soiling from a lightly soiled
load. Energy consumption will increase
with this option.



Select the setting you want and
confirm with

OK

.

«
...
95
96
97
98
99
...
»

Summary of Contents for G 6993









































































































Reviews:

No comments

Related manuals for G 6993

Brand: Campomatic Pages: 25

Brand: Gaggenau Pages: 40

Brand: PARRY Pages: 15

Brand: Daewoo Pages: 36

Brand: IFB Pages: 14

Brand: Amica Pages: 2

Brand: minibaby Pages: 9

Brand: V-ZUG Pages: 76

Brand: Infiniton Pages: 67

Brand: Samsung Pages: 64

Brand: Samsung Pages: 68

Brand: Samsung Pages: 112

WW9 J5 6 Series

Brand: Samsung Pages: 272

Brand: Samsung Pages: 60

WW8 T301 Series

Brand: Samsung Pages: 610

Brand: Samsung Pages: 52

Brand: Haier Pages: 20

Brand: Electrolux Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands