Miele G 6993 Operating Instructions Manual Download Page 69

Page: 69 / 104

Problem solving guide

Issue

Cause and remedy

All in-operation
indicators are flashing
quickly.
The warning buzzer is
sounding.
One of the following
faults is shown in the
display:

Before rectifying the problem:



Switch the dishwasher off using the



sensor.



Technical fault FXX

There may be a technical fault.

After a few seconds:



Switch the dishwasher back on.



Select the programme you want.



Close the door.

If the fault message appears again, there is a
technical fault.



Call your Miele dealer.



Waterproof fault

The Waterproof system has reacted.



Close the stopcock.



Call your Miele dealer.



Technical fault F78

A fault has occurred in the circulation pump.



Switch the dishwasher off for at least 30 seconds
with the



sensor.



Switch the dishwasher back on.



Select the programme you want.



Close the door.

If the fault message appears again, there is a
technical fault.



Call your Miele dealer.

Summary of Contents for G 6993









































































































Search results

Summary of Contents for G 6993

Reviews:

Related manuals for G 6993

Brands by name

Popular brands

Miele G 6993, Operating Instructions Manual

Search results

Summary of Contents for G 6993

Reviews:

Related manuals for G 6993

Brands by name

Popular brands