Miele G 6993 Operating Instructions Manual Download Page 20

Page: 20 / 104

Before using for the first time

Opening the door

This dishwasher has a motorised door
opener which is activated by knocking
on the door front ("Knock2open
function").



Knock twice in quick succession on
the top third of the door front

The door will open a little.



There are two dark grips inside the
door at the top.
Take hold of them and pull to release
the door lock.

The door locking pins will retract.

If the door is opened during operation
all functions are automatically
interrupted.

The number of knocks required for
opening the door can be changed if
wished (see "Settings, Knock2open").



Water in the dishwasher may be

hot. Danger of scalding.
Only open the door during operation
if absolutely necessary and exercise
extreme caution when doing so.



Keep the area around the door

free of obstructions.

At the end of programmes with a drying
phase (see "Programme chart"), the
door will open automatically a little in
order to help the drying process.
This function can be deactivated, if
preferred (see "Settings menu,
AutoOpen").

Summary of Contents for G 6993









































































































Search results

Summary of Contents for G 6993

Reviews:

Related manuals for G 6993

Brands by name

Popular brands

Miele G 6993, Operating Instructions Manual

Search results

Summary of Contents for G 6993

Reviews:

Related manuals for G 6993

Brands by name

Popular brands