Miele G 6993 Operating Instructions Manual Download Page 85 | Manualshive

Page: 85 / 104

background image

Plumbing

85

The Miele waterproof anti-leak
system

Provided your dishwasher has been
installed correctly, the Miele WaterProof
System will protect you from water
damage throughout its lifetime.

Connection to the water supply



Water in the dishwasher must

not be used as drinking water.

– The dishwasher may be connected to

a cold or hot water supply, max.
60 °C.
We would only recommend
connection to a hot water supply if it
is economical, e.g. a solar powered
supply. When connected to a hot
water supply all programme stages
which would otherwise be carried out
with cold water will be carried out
with hot water.

– The

SolarSave

programme (if

available) requires a hot water supply
of between 45 °C (minimum) and 60
°C (maximum).
The higher the water intake
temperature, the better the cleaning
and drying results.

«
...
83
84
85
86
87
...
»

Summary of Contents for G 6993









































































































Reviews:

No comments

Related manuals for G 6993

Brand: Jenn-Air Pages: 40

Brand: Jenn-Air Pages: 3

Brand: DAEWOO ELECTRONICS Pages: 28

Brand: Samsung Pages: 96

Brand: Asko Pages: 16

Brand: Roper Pages: 36

Brand: Primotecq Pages: 72

Brand: Speed Queen Pages: 1

Brand: Roper Pages: 36

Brand: Hotpoint Pages: 20

Brand: Bradley Pages: 5

Brand: Asko Pages: 32

Brand: Salora Pages: 77

Brand: Samsung Pages: 80

Brand: Candy Pages: 124

Brand: Primus Pages: 112

Brand: Black & Decker Pages: 76

Brand: Black & Decker Pages: 100

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands