Miele G 6993 Operating Instructions Manual Download Page 56 | Manualshive

Page: 56 / 104

background image

Programme options

56

Heat exchanger

This dishwasher is equipped with a heat
exchanger, in which fresh water for the
programme is pre-heated, in order to
save energy. The heat exchanger is
refilled with fresh water towards the end
of each phase that uses fresh water and
is held there ready for the next part of
the programme.

If you do not wish to use this function it
can be switched off (see "Settings, Heat
exchanger").

If water in the heat exchanger is not
used for several weeks, it will be
automatically drained and pumped
away for hygiene reasons. This process
takes a few minutes and will also be
carried out if the dishwasher is
switched off or the door is open.
The display will remain dark. The
message

Empty accumulat.

will appear in

the display when the



button is

pressed. No other functions are
available during this process.
Automatic drainage cannot be
interrupted.

The heat exchanger can be manually
drained for transporting the appliance,
e.g. before moving house (see"Settings,
Heat exchanger").

The heat exchanger should only be
used in conjunction with a cold-fill
dishwasher.
This function should be switched off
if your dishwasher is connected to a
hot water supply.

«
...
54
55
56
57
58
...
»

Summary of Contents for G 6993









































































































Reviews:

No comments

Related manuals for G 6993

Brand: Ignis Pages: 28

Brand: Dacor Pages: 29

Brand: Samsung Pages: 68

WW7 J5 6 Series

Brand: Samsung Pages: 48

Brand: Samsung Pages: 118

Brand: Samsung Pages: 6

Brand: Samsung Pages: 44

Brand: Samsung Pages: 10

Brand: Samsung Pages: 80

Brand: Samsung Pages: 22

Brand: Samsung Pages: 264

Brand: Samsung Pages: 40

Brand: Samsung Pages: 40

Brand: Samsung Pages: 112

Brand: Alliance Laundry Systems Pages: 32

Brand: Sandstrom Pages: 36

Brand: Heinner Pages: 58

Brand: Indesit Pages: 72

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands