Miele G 6993 Operating Instructions Manual Download Page 54

Page: 54 / 104

Programme options

Start at

With the

Start at

function, you set the

exact time you want the programme to
start at.



Use the



arrows to set the hour

and confirm with

The hours will be saved and the minute
number block will be highlighted.



Use the



arrows to set the

minutes and confirm with

The display will change to show the
programme menu.



Close the door.

The left hand in-operation indicator light
will start flashing on and off.

When the set time is reached, the
programme selected will begin
automatically.

Finish at

With the

Finish at

function, you set the

latest time at which you wish the
programme to end.



Use the



arrows to set the hour

and confirm with

The hours will be saved and the minute
number block will be highlighted.



Use the



arrows to set the

minutes and confirm with

The display will revert to the programme
menu and the estimated start time will
appear.



Close the door.

The left hand in-operation indicator light
will start flashing on and off.

A message will appear in the display if
the programme cannot be completed
by the set finish time because it has too
long a running time.

The selected programme will start
automatically when the estimated start
time is reached.

Summary of Contents for G 6993









































































































Search results

Summary of Contents for G 6993

Reviews:

Related manuals for G 6993

Brands by name

Popular brands

Miele G 6993, Operating Instructions Manual

Search results

Summary of Contents for G 6993

Reviews:

Related manuals for G 6993

Brands by name

Popular brands