Miele G 6993 Operating Instructions Manual Download Page 70

Page: 70 / 104

Problem solving guide

Issue

Cause and remedy

All in-operation
indicators are flashing
quickly.
The warning buzzer is
sounding.
One of the following
faults is shown in the
display:

Before rectifying the problem:



Switch the dishwasher off with the



button.

Fault auto. door closing

The door might be obstructed by an item inside the
appliance.



If this is the case, remove the item causing an
obstruction and switch the dishwasher on again.



If the same message appears again, call your
Miele dealer.

Fault auto. door opening

There may be a technical fault.



Open the door manually (see "Opening the door,
Emergency door opener").



If the same message appears again, call your
Miele dealer.

Summary of Contents for G 6993









































































































Search results

Summary of Contents for G 6993

Reviews:

Related manuals for G 6993

Brands by name

Popular brands

Miele G 6993, Operating Instructions Manual

Search results

Summary of Contents for G 6993

Reviews:

Related manuals for G 6993

Brands by name

Popular brands