manualshive.com logo in svg

Miele G 6900, Operating Instructions Manual, Page: 66 / 100

Share
Download
Miele G 6900 Operating Instructions Manual Download Page 66

Problem solving guide

66

Water inlet fault

Problem

Cause and remedy

The buzzer sounds. 

One of the following

fault messages appears

in the display:

 

Water inlet fault 

Please open the stopcock

The stopcock is closed.

Open the stopcock fully.

 

Water intake

Before rectifying the problem:

Switch the dishwasher off using the 

 sensor.

The water intake is restricted.

Open the stopcock fully and start the programme

again.

Clean the water inlet filter (see "Maintenance").

The water pressure at the intake is lower than 30

kPa (0.3 bar).

Seek professional advice.

The following message

appears in the display

during the 

SolarSave

programme:

 

Intake temp. too low

The intake water has not reached the required

temperature of 45°C (see "Plumbing, Connection to

the water supply").

Start the programme again.

If the fault message appears again, select a

different programme.

Summary of Contents for G 6900





































































































Reviews:

No comments