Miele G 6900 Page 68 Operating Instructions Manual Download

Page: 68 / 100

Problem solving guide

General problems

Problem

Cause and remedy

The display is dark.

The display has switched off automatically to save

energy.



Switch the dishwasher back on using the



sensor.

The interior lighting

does not come on when

the door is opened.

The lighting has been switched off permanently.



Switch the lighting back on again (see "Settings

menu, BrilliantLight").

The following fault

shows in the display:



Salt reservoir lid

During a programme

the warning buzzer will

also sound and the

programme will be

cancelled.

The salt reservoir lid has not been closed properly.



Close the salt reservoir lid.

If the salt reservoir lid has opened during a

programme:



Switch the dishwasher off and back on again with

the



sensor.



Close the salt reservoir lid.



Start the programme again.

Detergent residue is left

in the dispenser at the

end of a programme.

The dispenser was still damp when detergent was

added.



Make sure the dispenser is dry before adding

detergent.

The detergent

dispenser lid cannot be

closed properly.

Clogged detergent residue is blocking the catch.



Clean the detergent from the catch.

At the end of a

programme there is a

film of moisture on the

inside of the door and

the interior walls.

This is caused by the drying system and does not

indicate a fault. The moisture will dissipate after a

while.

Summary of Contents for G 6900





































































































Search results

Summary of Contents for G 6900

Reviews:

Related manuals for G 6900

Brands by name

Popular brands

Miele G 6900, Operating Instructions Manual

Search results

Summary of Contents for G 6900

Reviews:

Related manuals for G 6900

Brands by name

Popular brands