Miele G 6900 Page 64 Operating Instructions Manual Download

Page: 64 / 100

Problem solving guide

Most minor faults in the performance of the appliance, some of which may result

from incorrect operation, can be put right without contacting the Service

Department.
The following guide may help you to find the reason for a fault, and to correct it.

You should, however, note the following:



Unauthorised or incorrect repairs could cause personal injury or damage to

the appliance.
Repair work to electrical appliances should only be carried out by a suitably

qualified and trained person in strict accordance with current local and national

safety regulations. The manufacturer cannot be held liable for unauthorised

work.

Technical problems

Problem

Cause and remedy

The display remains

dark after the

dishwasher has been

switched on with the



sensor.

The appliance is not plugged in.



Insert the plug and switch on at the socket.

The mains fuse has tripped.



Reset the trip switch in the mains fuse box or

replace the fuse in the plug (minimum fuse rating -

see data plate).

The dishwasher stops

during a programme.

The mains fuse has tripped.



Reset the trip switch in the mains fuse box or

replace the fuse in the plug (minimum fuse rating -

see data plate).



If the mains fuse trips again, call the Miele Service

Department.

Summary of Contents for G 6900





































































































Search results

Summary of Contents for G 6900

Reviews:

Related manuals for G 6900

Brands by name

Popular brands

Miele G 6900, Operating Instructions Manual

Search results

Summary of Contents for G 6900

Reviews:

Related manuals for G 6900

Brands by name

Popular brands