Miele ADVANTA G 1180 Operating Instructions Manual Download Page 40 | Manualshive

Page: 40 / 60

background image

With the aid of the following guide, minor problems can be easily corrected
without calling in a Miele service technician, saving you both time and money.

The following guide may help you to find the reason for a fault, and to correct it.
You should, however, note the following:

,

Repairs should only be carried out by a suitably qualified and trained

person in accordance with current local and national safety regulations.
Unauthorised or incorrect repairs could cause personal injury or damage the
appliance.

Technical problems

Problem

Possible cause

Remedy

The appliance does
not start.

The door is not properly
closed.

Push the door firmly shut.

The appliance is not
plugged in.

Insert the plug and switch on
at the socket.

The fuse is defective or
has tripped.

Reset or replace the fuse.

The appliance is not
switched on.

Press the On button

g

, and

select a programme.

The dishwasher
stops during a
programme.

The fuse is defective or
has tripped.

Reset or replace the fuse.

Problem solving guide

40

«
...
38
39
40
41
42
...
»

Summary of Contents for ADVANTA G 1180





























































Reviews:

No comments

Related manuals for ADVANTA G 1180

Brand: Samsung Pages: 96

Brand: Panasonic Pages: 27

Brand: Dawlance Pages: 44

Brand: NEFF Pages: 25

Brand: Gorenje Pages: 30

Brand: Gaggenau Pages: 19

Brand: grandimpianti Pages: 85

Brand: Hoover Pages: 20

Brand: Lamona Pages: 28

Brand: AEG Electrolux Pages: 108

Brand: John Lewis Pages: 32

Brand: Kärcher Pages: 24

MVWC200X Series

Brand: Maytag Pages: 1

Brand: Maytag Pages: 48

Brand: Smeg Pages: 37

Brand: FAVORIT Pages: 40

Brand: Smeg Pages: 28

Brand: Haier Pages: 22

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands