Miele ADVANTA G 1180 Operating Instructions Manual Download Page 43 | Manualshive

Page: 43 / 60

background image

General problems

Problem

Possible cause

Remedy

Detergent residue is
left in the dispenser at
the end of a
programme.

The dispenser was still
damp when detergent was
added.

Make sure the dispenser is
dry before adding
detergent.

The detergent lid
cannot be closed
properly.

Clogged detergent residue
is blocking the catch.

Clean the detergent from
the catch.

At the end of a
programme there is a
film of moisture on
the inside of the door
and the interior walls.

This is caused by the
drying system and does not
indicate a fault.

The moisture will dissipate
after a short while.

Water remains in the
wash cabinet at the
end of a programme.

Before rectifying the
problem you must:

–

Switch the dishwasher
off with the Off button

o

.

The filter combination in the
wash cabinet is clogged.

Clean the filter
combination. See
"Cleaning and Care".

The drain pump or
non-return valve may be
blocked.

Clean the drain pump or
the non-return valve. See
"Problem solving".

The drain hose is kinked.

Remove any kink from the
drain hose.

Problem solving guide

43

«
...
41
42
43
44
45
...
»

Summary of Contents for ADVANTA G 1180





























































Reviews:

No comments

Related manuals for ADVANTA G 1180

Brand: IFB Pages: 24

Brand: GEAppliances Pages: 72

Brand: Gaggenau Pages: 64

Brand: Bush Pages: 25

Brand: Acorn Safety Pages: 4

Brand: NEC Pages: 17

Brand: Hanseatic Pages: 78

Brand: Daewoo Pages: 58

Brand: Hotpoint Pages: 24

Brand: Smeg Pages: 42

Brand: Bradley Pages: 5

Brand: Hotpoint Pages: 28

Brand: Samsung Pages: 60

Brand: Samsung Pages: 68

Brand: Samsung Pages: 68

WD752U4BK Series

Brand: Samsung Pages: 88

WD702U4BK Series

Brand: Samsung Pages: 88

Brand: Samsung Pages: 118

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands