Miele ADVANTA G 1180 Operating Instructions Manual Download Page 20 | Manualshive

Page: 20 / 60

background image

Setting the rinse aid dosage

You can adjust the rinse aid dosage for
best results.

The rinse aid dosage can be set from
approx. 0-6 ml. It is set to a
recommended setting of approx. 3 ml
at the factory.

If spots appear on crockery and
glassware:

^

Increase the rinse aid dosage.

If clouding or smearing appears on
crockery and glassware:

^

Decrease the rinse aid dosage.

^

Switch the dishwasher off with the Off
button

o

.

^

Press the programme selector button
in, and

whilst holding it in

switch

the dishwasher on using the On
button

g

.

Keep the programme selector button
pressed in for at least four seconds
until the lower right hand programme
indicator comes on.

If this does not happen, start the
procedure from the beginning again.

^

Press the programme selector button
three times briefly.

The "Inlet/Drain" check light will flash
briefly three times at intervals.

The upper right hand programme
indicator will flash briefly three times at
intervals.
This means that approx. 3 ml of rinse
aid will be used per programme
(factory default setting).

The number of times the upper right
hand programme indicator flashes tells
you the rinse aid dosage which has
been set (see chart).

Rinse aid

in ml

Flashing

0

-

1

Once

2

Twice

3

Three times

4

Four times

5

Five times

6

Six times

^

Press the programme selector button
for at least one second until the
upper right hand programme
indicator comes on.

^

Press the programme selector button
briefly to select the number of flashes
which equate to the rinse aid dosage
you want.
Each press on the button moves you
up a level.

The programmed rinse aid dosage is
now stored in memory.

^

Switch the dishwasher off with the Off
button

o

.

Before using for the first time

20

«
...
18
19
20
21
22
...
»

Summary of Contents for ADVANTA G 1180





























































Reviews:

No comments

Related manuals for ADVANTA G 1180

Brand: Hansa Pages: 2

Brand: Hansa Pages: 2

Brand: Maidaid Halcyon Pages: 15

Brand: Indesit Pages: 84

Brand: GE Pages: 60

Brand: Asko Pages: 36

Brand: Jenn-Air Pages: 14

Brand: Hoover Pages: 17

Brand: AEG Electrolux Pages: 48

Brand: GE Pages: 70

Brand: Smeg Pages: 14

Brand: Heinner Pages: 59

HG6085D137609HW

Brand: Hanseatic Pages: 78

Brand: Cooke & Lewis Pages: 136

Brand: Smeg Pages: 15

Brand: NEFF Pages: 72

Brand: Haier Pages: 19

Brand: Haier Pages: 18

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands