Miele ADVANTA G 1180 Operating Instructions Manual Download Page 33 | Manualshive

Page: 33 / 60

background image

Interrupting a programme

A programme is interrupted as soon as
the door is opened.
If the door is closed again, the
programme will continue from the point
it was at before the door was opened.

,

Water in the dishwasher may be

hot. Danger of scalding!
Only open the door if absolutely
necessary and exercise extreme
caution when doing so. Before
closing the door again, leave it ajar
for approx. 20 seconds. This will
enable the temperature in the wash
cabinet to settle. Then close the
door firmly making sure that it clicks
into place.

Changing a programme

Important:
If the detergent dispenser flap has
already opened, do not change the
programme.

If a programme has already started and
you wish to change it, proceed as
follows:

^

Open the door.

^

Press the Off button

o

.

^

Press the On button

g

.

^

Select the programme required using
the programme selector button.

^

Close the door.

The programme cycle will begin.

Operation

33

«
...
31
32
33
34
35
...
»

Summary of Contents for ADVANTA G 1180





























































Reviews:

No comments

Related manuals for ADVANTA G 1180

Brand: Washtech Pages: 40

Brand: Samsung Pages: 10

Brand: Samsung Pages: 9

Brand: Samsung Pages: 7

Brand: Samsung Pages: 12

Brand: Asko Pages: 24

Brand: Kuppersbusch Pages: 33

Brand: Indesit Pages: 24

Brand: Maytag Pages: 20

Brand: Indesit Pages: 72

Brand: Samsung Pages: 76

Brand: Electrolux Pages: 28

Brand: Electrolux Pages: 28

Brand: Electrolux Pages: 43

Brand: Electrolux Pages: 28

Brand: Electrolux Pages: 35

Brand: Electrolux Pages: 24

Brand: Electrolux Pages: 23

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands