Miele ADVANTA G 1180 Operating Instructions Manual Download Page 35 | Manualshive

Page: 35 / 60

background image

Factory default setting

If you have altered any settings from
the factory default, you can re-set them
back to the factory default settings as
follows:

^

Open the door.

^

Switch the dishwasher off with the Off
button

o

.

^

Press the programme selector button
in, and

whilst holding it in

switch

the dishwasher on using the On
button

g

.

Keep the programme selector button
pressed in for at least four seconds
until the lower right hand programme
indicator comes on.

If this does not happen, start the
procedure from the beginning again.

^

Press the programme selector button
briefly 12 times.

The "Inlet/Drain" check light will give
one long flash and two brief flashes at
intervals.

The upper right hand indicator shows
whether a setting other than the factory
default setting has been set.

– If the upper right hand indicator is

flashing:
All settings are factory default
settings.

– If the upper right hand indicator is

not lit up:
At least one setting has been altered
from the factory default setting.

^

If you want to re-set the factory
default settings, press the
programme selector button for at
least one second until the "Inlet/Drain"
check light comes on.

^

Press the programme selector button
briefly.

The setting is now stored in memory.

^

Switch the dishwasher off with the Off
button

o

.

Operation

35

«
...
33
34
35
36
37
...
»

Summary of Contents for ADVANTA G 1180





























































Reviews:

No comments

Related manuals for ADVANTA G 1180

Brand: ECG Pages: 188

Brand: ECG Pages: 188

Brand: SOGEDIS Pages: 23

Brand: DELLA Pages: 7

Brand: Smeg Pages: 26

FP-90LST060GMTL-N

Brand: Midea Pages: 5

Brand: Winterhalter Gastronom Pages: 19

Brand: FRAM Pages: 59

Brand: Amana Pages: 16

Brand: Hobart Pages: 18

Brand: Indesit Pages: 72

Brand: ZANKER Pages: 60

Brand: Daewoo Pages: 41

Brand: Fisher & Paykel Pages: 40

Brand: NEFF Pages: 56

Brand: Samsung Pages: 73

Brand: Samsung Pages: 76

Brand: Samsung Pages: 76

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands