Miele ADVANTA G 1180 Operating Instructions Manual Download Page 42 | Manualshive

Page: 42 / 60

background image

The dishwasher does not fill/drain

Problem

Possible cause

Remedy

The dishwasher
stops working
shortly after the start
of the programme.
The buzzer sounds.
The Inlet/Drain check
indicator flashes
when the door is
opened.

The stopcock is
closed.

–

Open the stopcock fully.

The dishwasher
stops during a
programme.
The buzzer sounds.
The Inlet/Drain check
indicator flashes
when the door is
opened.

Before rectifying the problem you
must:

–

Switch the dishwasher off with the
Off button

o

.

Water intake is
restricted.

–

Open the stopcock fully.

–

Clean the water inlet filter (see
"Problem solving").

–

The water pressure at the intake is
lower than 30 kPa (0.3 bar).
Seek professional advice.

Water outlet is
restricted, water
remains in the
wash cabinet at
the end of a
programme.

–

Clean the filter combination. See
"Cleaning and Care".

–

Clean the drain pump. See
"Problem solving".

–

Clean the non-return valve. See
"Problem solving".

–

Remove any kink in the drain
hose.

Problem solving guide

42

«
...
40
41
42
43
44
...
»

Summary of Contents for ADVANTA G 1180





























































Reviews:

No comments

Related manuals for ADVANTA G 1180

Brand: GE Pages: 24

Brand: GE Pages: 2

Brand: Gaggenau Pages: 40

Brand: Indesit Pages: 72

Brand: Colged Pages: 112

Brand: Zanussi Electrolux Pages: 28

Brand: Atag Pages: 116

Brand: Benton Harbor Pages: 7

Brand: Dawlance Pages: 4

HG4585D107636QW

Brand: Hanseatic Pages: 82

Brand: WESCO NAVY Pages: 186

Brand: Solt Pages: 11

Brand: Gorenje Pages: 29

Brand: Eswood Pages: 17

Brand: Hotpoint Pages: 76

Brand: Hotpoint Pages: 2

Brand: Arctic Pages: 60

Brand: Samsung Pages: 520

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands