background image

Microframe Corporation

Series 3061 - DataTrack Waiter Call

10

3  SYSTEM OVERVIEW

3.1 DESCRIPTION

The Scope DataTrack Waiter Call is a desk-

top or wall mount radio transcoder that can be

used to transmit numeric and multi-call/pulsed

vibrate messages direct to pagers carried by

individuals or entire groups.  The system has 14

individual call buttons that can transmit any of

three different call types direct to the user’s

pager.

3.2 RANGE EXPANSION

The range and performance of this equip-

ment can be improved by the addition of more

efficient antennas.* These can be installed

either inside or outside the building and are

connected to the transmitter with 50 OHM

coaxial cable.

The center-fed half wave dipole, measuring

approximately 12 inches from tip to tip, will

provide excellent all round local signaling.  It is

a light duty antenna suitable for sheltered

environments/internal installation (LUHFDP).

It includes a 15 foot cable.

NOTE: High frequencies can equate to high

power losses. Always use quality cable. RG58 is

only acceptable on cable runs of up to 5 meters.

We recommend RG213, or equivalent, on

greater lengths. If in doubt consult your dealer.

*Subject to license conditions. Specifically,

mounting height and Effective Radiated Power

(ERP)

.

3.3 IMPORTANT INFORMATION

It is the purchaser's responsibility to deter-

mine the suitability of this equipment and its

derivatives for any given application.

Good working practice dictates that a suit-

able system installation log must be generated,

together with a record of the dates when the

system has been manually checked, (with the

aid of signal strength meters, etc.) enabling the

system performance to be compared with the

original installation data.

3.4 SAFETY INFORMATION

These products are designed to operate safely

when installed and used according to general

safety practices.  The following requirements

should be observed at all times:

Do NOT subject this equipment to:

Mechanical shock

Excessive humidity or moisture

Extremes of temperature

Corrosive liquids

This equipment is designed for indoor use,

unless expressly stated otherwise, and must

not be used in classified Hazardous Areas,

including areas containing explosive or flam-

mable vapors, unless express authorization has

been given in writing by the manufacturer.  If

in doubt, consult Microframe for further infor-

mation.

Do not obstruct any slots or openings in the

product.  These are provided for ventilation to

ensure reliable operation of the product and to

protect it from overheating.

3.5 CARING FOR TRANSMITTER

Only use a damp cloth for cleaning (not

liquid or aerosol-based cleaners), and ensure

that any power is removed from the unit prior

to beginning the cleaning operation.

Removal of covers from the equipment must

only be undertaken by authorized service per-

sonnel, who must ensure that power is isolated

prior to removal.

3.6 LIABILITY

Scope and Microframe do not accept liability

for any damage or injury, caused as the result

of misuse of this equipment. It is the responsi-

bility of the user to ensure that the equipment

is operated in the manner for which it was

intended and that it is the correct item of

equipment for the required task.

3.7 WARRANTY INVALIDATION

Alteration or modification to any part of this

equipment, without the prior written consent

of the manufacturer, will invalidate all manu-

facturer approvals and warranties.  No adjust-

ments can be undertaken except by qualified

and licensed persons as defined by the FCC

Rules and Regulations. Operation of altered

equipment can result in fines, imprisonment,

and/or confiscation of such equipment.

3.8 SERVICE INFORMATION

If you experience a problem with your equip-

ment, please contact Microframe at

1-800-635-3811.

Summary of Contents for 3061 Series














Reviews: